Dec 11, 2025Leave a message

What is the impact strength of POM extruded parts?

POM (Polyoxymethylene), also known as acetal or polyacetal, is a high - performance engineering thermoplastic widely used in various industries. As a POM extruded parts supplier, I have in - depth knowledge of the material and its properties, especially the impact strength of POM extruded parts. In this blog, we will explore what impact strength is, how it is measured, the factors affecting the impact strength of POM extruded parts, and its significance in real - world applications.

PBT Extruded PartsNylon Extruded Parts

What is Impact Strength?

Impact strength is a measure of a material's ability to withstand sudden and high - force impacts without breaking or fracturing. It reflects the material's toughness and its capacity to absorb energy during an impact event. For POM extruded parts, impact strength is a crucial property as these parts are often used in applications where they may be subjected to shock loads, such as in automotive components, mechanical equipment, and consumer products.

There are different types of impact tests used to measure the impact strength of materials, including the Izod impact test and the Charpy impact test. In the Izod impact test, a notched specimen is fixed vertically, and a pendulum strikes the specimen at the notch. The energy absorbed by the specimen during the breakage is measured, and this energy value is used to represent the impact strength. The Charpy impact test is similar, but the specimen is supported horizontally, and the pendulum strikes the middle of the specimen.

Measuring the Impact Strength of POM Extruded Parts

When measuring the impact strength of POM extruded parts, it is important to follow standardized testing procedures. The test specimens should be prepared according to the relevant standards, such as ASTM or ISO standards. These standards specify the dimensions, notch geometry, and testing conditions to ensure consistent and comparable results.

The impact strength of POM can vary depending on the grade of the material. General - purpose POM grades typically have a certain level of impact resistance, but there are also high - impact grades available. High - impact POM grades are formulated with additives or modifiers to enhance their ability to absorb energy during an impact. For example, some high - impact POM grades may contain elastomeric modifiers that can improve the material's ductility and toughness.

Factors Affecting the Impact Strength of POM Extruded Parts

1. Molecular Structure

The molecular structure of POM plays a significant role in its impact strength. POM has a highly crystalline structure, which gives it excellent mechanical properties, including stiffness and strength. However, the high crystallinity can also make the material more brittle, reducing its impact strength. By controlling the degree of crystallinity during the extrusion process, it is possible to optimize the impact strength of POM extruded parts. For example, slow cooling during extrusion can lead to larger crystal sizes, which may decrease the impact strength, while rapid cooling can result in smaller crystal sizes and potentially improve the impact resistance.

2. Additives and Fillers

Additives and fillers can have a profound effect on the impact strength of POM extruded parts. As mentioned earlier, elastomeric additives can be used to improve the impact resistance of POM. These additives act as shock absorbers, dissipating the energy from an impact and preventing crack propagation. On the other hand, some fillers, such as glass fibers, can increase the stiffness of POM but may also reduce its impact strength if not properly dispersed. The type, amount, and dispersion of additives and fillers need to be carefully controlled to achieve the desired balance between impact strength and other mechanical properties.

3. Processing Conditions

The extrusion process parameters also influence the impact strength of POM extruded parts. Temperature, pressure, and screw speed are some of the key processing variables. If the extrusion temperature is too high, the POM material may degrade, leading to a decrease in impact strength. Similarly, improper pressure and screw speed can cause uneven flow and stress distribution in the extruded part, which can weaken the part and reduce its impact resistance.

4. Part Design

The design of the POM extruded part itself can affect its impact strength. Sharp corners and notches in the part design can act as stress concentrators, increasing the likelihood of crack initiation during an impact. By using rounded corners and smooth transitions in the part design, the stress concentration can be reduced, and the impact strength can be improved.

Significance of Impact Strength in Real - World Applications

The impact strength of POM extruded parts is of great importance in many real - world applications.

Automotive Industry

In the automotive industry, POM extruded parts are used in various components, such as door locks, seat belt buckles, and fuel system components. These parts need to have sufficient impact strength to withstand the vibrations, shocks, and sudden impacts that occur during normal driving and in the event of a collision. For example, a seat belt buckle made of POM with high impact strength can ensure the safety of passengers by reliably holding the seat belt in place even under high - force impacts.

Mechanical Equipment

In mechanical equipment, POM extruded parts are often used in gears, bearings, and couplings. These parts are subject to dynamic loads and impacts during the operation of the equipment. A gear made of POM with good impact strength can resist the sudden forces generated during gear meshing and prevent premature failure, ensuring the smooth operation of the mechanical equipment.

Consumer Products

In consumer products, such as household appliances and toys, POM extruded parts are used for their durability and mechanical properties. For example, the buttons on a remote control or the hinges on a toy may be made of POM. High impact strength ensures that these parts can withstand the repeated use and occasional drops or impacts, providing a long - lasting and reliable performance.

Comparison with Other Extruded Parts

When considering the impact strength, it is also interesting to compare POM extruded parts with other types of extruded parts, such as Nylon Extruded Parts, PBT Extruded Parts, and Polyurethane Extruded Parts.

Nylon extruded parts generally have good impact strength, especially in high - moisture environments. Nylon can absorb moisture, which can act as a plasticizer and improve its impact resistance. However, POM has better dimensional stability and lower water absorption compared to nylon, which may be more suitable for applications where precise dimensions and low moisture sensitivity are required.

PBT extruded parts are known for their excellent electrical insulation properties and chemical resistance. While PBT also has a certain level of impact strength, POM typically offers higher stiffness and better fatigue resistance, making it a better choice for applications with high - stress and repeated impact requirements.

Polyurethane extruded parts are very flexible and have excellent shock - absorbing properties. They are often used in applications where high elasticity and impact absorption are needed, such as in bumpers and vibration dampers. However, POM provides better mechanical strength and stiffness, which may be more appropriate for applications that require a combination of strength and impact resistance.

Conclusion

The impact strength of POM extruded parts is a critical property that is influenced by multiple factors, including molecular structure, additives, processing conditions, and part design. Understanding these factors and how they interact is essential for producing high - quality POM extruded parts with the desired impact strength.

As a POM extruded parts supplier, we have the expertise and experience to optimize the impact strength of our products according to the specific requirements of different applications. Whether you need POM extruded parts for the automotive industry, mechanical equipment, or consumer products, we can provide customized solutions to meet your needs.

If you are interested in our POM extruded parts and would like to discuss your specific requirements or have any questions about the impact strength or other properties of our products, please feel free to contact us for procurement and further discussions.

References

  • ASTM International standards on plastics testing
  • ISO standards related to impact testing of plastics
  • Technical literature from POM resin manufacturers

Send Inquiry

Home

Phone

E-mail

Inquiry